Hi flatmax,
I received my Octo sound card today in the USA and set it up. I was able to stack the Octo on top of my Pi3B and official 7" touchscreen with a MoPower UPS on top of the Octo (using a stacking header and some doubled-up standard-height hat standoff screws to get it high enough over the ribbon cable port -- I can post a photo if anybody is interested). It would be nice if the kit came with four of the plastic standoff screws (might be a little more secure) instead of just two, but not completely necessary and maybe you could just recommend where to purchase more of the same plastic standoff screws. I've only tested it so far by playing music in Audacious through a small bookshelf speaker stereo system. It sounds excellent! Thank you very much for your hard work.
One thing I'm curious about -- what are the included potentiometer knobs for? Are these related to the preamp for the balanced TRS breakout board which I'll receive later? Or are they just included in case I want to somehow add custom volume or fader controls? I'm also curious about the two pins on the underside of the Octo. Perhaps some further hardware documentation would be helpful for everyone when you have some time.
Thanks again,
KTB
Octo arrived and working, potentiometer knobs?
Moderator: flatmax
Re: Octo arrived and working, potentiometer knobs?
I would be very keen to see a picture of your setup.
Oh potentiometer knobs !
OK, we are still ironing out the finer details of packaging. You were meant to receive the necessary standoff screws for this card and no potentiometer knobs.
I'll chat with the crew in China and change this in the future - in the rush to get the items to you and make sure the work, we brushed over these details, apologies.
If you want to get some of these plastic spacers, then you should source M2.5 mm threads of length around 6mm or so, with plastic spacer lengths of 12 mm.
thanks
Matt
Oh potentiometer knobs !
OK, we are still ironing out the finer details of packaging. You were meant to receive the necessary standoff screws for this card and no potentiometer knobs.
I'll chat with the crew in China and change this in the future - in the rush to get the items to you and make sure the work, we brushed over these details, apologies.
If you want to get some of these plastic spacers, then you should source M2.5 mm threads of length around 6mm or so, with plastic spacer lengths of 12 mm.
thanks
Matt
Check out our audiophile quality crossovers : https://bit.ly/2kb1nzZ
Please review the Zero sound card on Amazon USA : https://www.amazon.com/dp/B075V1VNDD
---
Check out our new forum on github : https://github.com/Audio-Injector
Please review the Zero sound card on Amazon USA : https://www.amazon.com/dp/B075V1VNDD
---
Check out our new forum on github : https://github.com/Audio-Injector
Re: Octo arrived and working, potentiometer knobs?
Well, my system worked great for about a day. I had rebooted at least a few times without any issues.
I'm not sure what's going wrong at this point. From my perspective, all I did was try to test out shairport-sync (which I had working previously using the analog output on the Pi3B without the Octo) and something seems to have gone very wrong. The Octo stopped working and it seems the onboard WiFi I was using for an access point stopped working too (I'm not sure if the issues are related. The onboard Bluetooth still seemed to work fine.
Then for several boot/reboot attempts with the Octo and access point not working, the following lines from dmesg seemed like they may be relevant:
I checked the micro SD card for errors and it appears to be fine. sudo vcdbg log msg doesn't report any Device Tree problems.
I unplugged the power for a while, then booted it up again and the Octo loaded and worked OK (the access point is still not working, but perhaps that's unrelated to the Octo not working). However, I am seeing "I2S SYNC error!" messages in dmesg.
This all happened with kernel 4.9.24-v7+. I suppose my next step is to disassemble everything and try running the Octo and Pi3B without the MoPower UPS and perhaps without the official touchscreen as well. I'll also probably try just running the Pi3B on its own with an HDMI screen. Perhaps that will isolate the problem and help determine what might be going wrong. I suppose it might be a power issue, but I really have no idea at this point.
I'm not sure what's going wrong at this point. From my perspective, all I did was try to test out shairport-sync (which I had working previously using the analog output on the Pi3B without the Octo) and something seems to have gone very wrong. The Octo stopped working and it seems the onboard WiFi I was using for an access point stopped working too (I'm not sure if the issues are related. The onboard Bluetooth still seemed to work fine.
Then for several boot/reboot attempts with the Octo and access point not working, the following lines from dmesg seemed like they may be relevant:
Code: Select all
[ 45.405938] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 45.406325] cs42xx8: probe of 1-0048 failed with error -121
...
[ 46.075276] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 46.075294] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
...
[ 47.635392] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 47.635415] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
...
[ 55.888713] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 58.218621] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7I checked the micro SD card for errors and it appears to be fine. sudo vcdbg log msg doesn't report any Device Tree problems.
I unplugged the power for a while, then booted it up again and the Octo loaded and worked OK (the access point is still not working, but perhaps that's unrelated to the Octo not working). However, I am seeing "I2S SYNC error!" messages in dmesg.
Code: Select all
[ 12.897445] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 12.937068] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 12.940784] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 12.953425] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 13.206045] brcmfmac: power management disabled
[ 14.225767] Bluetooth: HCI UART driver ver 2.3
[ 14.225780] Bluetooth: HCI UART protocol H4 registered
[ 14.225784] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 14.226291] Bluetooth: HCI UART protocol Broadcom registered
[ 14.238023] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 14.238041] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 14.796935] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 14.796946] Bluetooth: BNEP filters: protocol multicast
[ 14.796961] Bluetooth: BNEP socket layer initialized
[ 15.059066] Bluetooth: RFCOMM TTY layer initialized
[ 15.059090] Bluetooth: RFCOMM socket layer initialized
[ 15.059111] Bluetooth: RFCOMM ver 1.11
[ 15.432152] brcmfmac: power management disabled
[ 16.300501] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 16.390277] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 18.623518] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
[ 19.947664] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 19.948288] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 20.469988] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 22.550106] fuse init (API version 7.26)
[ 40.607172] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 40.637332] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 40.640923] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 40.648522] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 45.800605] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
[ 331.073379] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 331.073971] bcm2835-i2s 3f203000.i2s: I2S SYNC error!This all happened with kernel 4.9.24-v7+. I suppose my next step is to disassemble everything and try running the Octo and Pi3B without the MoPower UPS and perhaps without the official touchscreen as well. I'll also probably try just running the Pi3B on its own with an HDMI screen. Perhaps that will isolate the problem and help determine what might be going wrong. I suppose it might be a power issue, but I really have no idea at this point.
Re: Octo arrived and working, potentiometer knobs?
Hi there, not sure what's happening here.
The i2s sync errors aren't related tot the October, they are something to do with the bcm2835-i2s driver. These happen with most of the pi sound cards. My understanding is that they are harmless.
We should.monitor this.issue, to see how often your system doesn't load the Octo. I wonder if anything else is effecting it in some unknown way.
Matt
The i2s sync errors aren't related tot the October, they are something to do with the bcm2835-i2s driver. These happen with most of the pi sound cards. My understanding is that they are harmless.
We should.monitor this.issue, to see how often your system doesn't load the Octo. I wonder if anything else is effecting it in some unknown way.
Matt
Check out our audiophile quality crossovers : https://bit.ly/2kb1nzZ
Please review the Zero sound card on Amazon USA : https://www.amazon.com/dp/B075V1VNDD
---
Check out our new forum on github : https://github.com/Audio-Injector
Please review the Zero sound card on Amazon USA : https://www.amazon.com/dp/B075V1VNDD
---
Check out our new forum on github : https://github.com/Audio-Injector
Re: Octo arrived and working, potentiometer knobs?
I've done a little more testing without disassembling everything.
It seems that when I have the vc4-fkms-v3d overlay enabled (I've been using that for a while now without any big problems), the Octo fails to load consistently. The first day of using the Octo, it seemed to work fine. I wonder if enabling vc4-fkms-v3d increases the power requirements just enough to become a problem. Now that I think about it, It's also possible that I had been using 4.9.20-v7+ or 4.9.22-v7+ at first. Unfortunately, I do not remember. I may try rolling back to one of those earlier kernel versions just to check it out.
Without vc4-fkms-v3d enabled:
With vc4-fkms-v3d enabled:
I then tried having the vc4-fkms-v3d overlay enabled, but lowered v3d_freq down to 300. While the Octo fails to register at first, it does apparently work the second time.
With vc4-fkms-v3d enabled, v3d_freq=300:
Based on some things I've read, while the I2S SYNC error! may not be anything to worry about, the bcm2835-dma 3f007000.dma: DMA transfer could not be terminated might indicate something to be concerned about. I don't really know.
The MoPower UPS was really designed with the power requirements of the Pi2B (before the release of the Pi3B and its higher power usage). I use a nice powered USB hub for everything other than the touchscreen, Pi3B, Octo and MoPower UPS. It's possible I've just reached the limits of what the MoPower UPS can reliably do.
It seems that when I have the vc4-fkms-v3d overlay enabled (I've been using that for a while now without any big problems), the Octo fails to load consistently. The first day of using the Octo, it seemed to work fine. I wonder if enabling vc4-fkms-v3d increases the power requirements just enough to become a problem. Now that I think about it, It's also possible that I had been using 4.9.20-v7+ or 4.9.22-v7+ at first. Unfortunately, I do not remember. I may try rolling back to one of those earlier kernel versions just to check it out.
Without vc4-fkms-v3d enabled:
Code: Select all
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
dtparam=sd_overclock=63
#dtparam=audio=on
#audio_pwm_mode=1
#audio_pwm_mode=2
dtoverlay=audioinjector-addons
enable_uart=1
lcd_rotate=2
ignore_lcd=0
#total_mem=1024
#gpu_mem=32
gpu_mem=128
#dtoverlay=vc4-kms-v3d,cma-256,rpi-ft5406
#dtoverlay=vc4-fkms-v3d,cma-192,rpi-ft5406
dtoverlay=rpi-ft5406
arm_freq=1200
arm_freq_min=600
core_freq=250
core_freq_min=250
h264_freq=300
isp_freq=250
v3d_freq=500
avoid_pwm_pll=1
#sdram_freq=450
#sdram_schmoo=0x02000020
#over_voltage=2
#over_voltage_sdram=2
decode_MPG2=0x3ab16f03
decode_WVC1=0x438a78fbCode: Select all
pi@raspberrypi:~$ vcgencmd get_throttled
throttled=0x0Code: Select all
[ 6.509837] audioinjector-octo soc:sound: cs42448 <-> 3f203000.i2s mapping ok
[ 8.792179] uart-pl011 3f201000.serial: no DMA platform data
[ 8.878927] random: crng init done
[ 8.975989] Bluetooth: Core ver 2.22
[ 8.976141] NET: Registered protocol family 31
[ 8.976152] Bluetooth: HCI device and connection manager initialized
[ 8.976177] Bluetooth: HCI socket layer initialized
[ 8.976195] Bluetooth: L2CAP socket layer initialized
[ 8.976242] Bluetooth: SCO socket layer initialized
[ 9.858985] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 9.998161] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 11.365735] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 12.296094] brcmfmac: power management disabled
[ 12.587494] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 12.627160] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 12.634446] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 12.645356] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 12.814244] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 12.814270] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 14.012963] brcmfmac: power management disabled
[ 14.315257] Bluetooth: HCI UART driver ver 2.3
[ 14.315266] Bluetooth: HCI UART protocol H4 registered
[ 14.315269] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 14.315392] Bluetooth: HCI UART protocol Broadcom registered
[ 14.371384] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 14.788490] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 14.788505] Bluetooth: BNEP filters: protocol multicast
[ 14.788528] Bluetooth: BNEP socket layer initialized
[ 14.813274] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 14.955158] Bluetooth: RFCOMM TTY layer initialized
[ 14.955208] Bluetooth: RFCOMM socket layer initialized
[ 14.955234] Bluetooth: RFCOMM ver 1.11
[ 19.465730] systemd[1]: apt-daily.timer: Adding 40min 38.627941s random time.
[ 19.930957] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 20.440022] systemd[1]: apt-daily.timer: Adding 54min 29.288933s random time.
[ 21.721501] fuse init (API version 7.26)
[ 21.755953] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
[ 33.366786] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 33.396947] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 33.400544] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 33.408332] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 38.569483] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
Code: Select all
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
dtparam=sd_overclock=63
#dtparam=audio=on
#audio_pwm_mode=1
#audio_pwm_mode=2
dtoverlay=audioinjector-addons
enable_uart=1
lcd_rotate=2
ignore_lcd=0
#total_mem=1024
#gpu_mem=32
gpu_mem=128
#dtoverlay=vc4-kms-v3d,cma-256,rpi-ft5406
dtoverlay=vc4-fkms-v3d,cma-192,rpi-ft5406
#dtoverlay=rpi-ft5406
arm_freq=1200
arm_freq_min=600
core_freq=250
core_freq_min=250
h264_freq=300
isp_freq=250
v3d_freq=500
avoid_pwm_pll=1
#sdram_freq=450
#sdram_schmoo=0x02000020
#over_voltage=2
#over_voltage_sdram=2
decode_MPG2=0x3ab16f03
decode_WVC1=0x438a78fbCode: Select all
pi@raspberrypi:~$ vcgencmd get_throttled
throttled=0x50000Code: Select all
[ 45.115372] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 45.115954] cs42xx8: probe of 1-0048 failed with error -121
[ 45.755011] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 45.755031] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 45.761857] vc4-drm soc:gpu: bound 3f600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 45.771398] ------------[ cut here ]------------
[ 45.771704] WARNING: CPU: 0 PID: 0 at drivers/gpu/drm/drm_irq.c:1794 drm_handle_vblank+0x298/0x29c [drm]
[ 45.771710] Modules linked in: snd_soc_cs42xx8_i2c snd_soc_cs42xx8 binfmt_misc joydev spidev vc4(+) brcmfmac drm_kms_helper brcmutil cfg80211 drm snd_soc_bcm2835_i2s snd_soc_audioinjector_octo_soundcard rfkill syscopyarea snd_soc_core sysfillrect snd_compress sysimgblt snd_pcm_dmaengine fb_sys_fops snd_pcm_oss snd_mixer_oss snd_pcm snd_timer i2c_bcm2835 spi_bcm2835 snd bcm2835_gpiomem rpi_ft5406 rpi_backlight uio_pdrv_genirq fixed uio evdev cdc_acm i2c_dev ip_tables x_tables ipv6
[ 45.771882] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.24-v7+ #993
[ 45.771887] Hardware name: BCM2835
[ 45.771925] [<8010fb3c>] (unwind_backtrace) from [<8010c058>] (show_stack+0x20/0x24)
[ 45.771944] [<8010c058>] (show_stack) from [<80455200>] (dump_stack+0xd4/0x118)
[ 45.771963] [<80455200>] (dump_stack) from [<8011d2c4>] (__warn+0xf8/0x110)
[ 45.771978] [<8011d2c4>] (__warn) from [<8011d3ac>] (warn_slowpath_null+0x30/0x38)
[ 45.772227] [<8011d3ac>] (warn_slowpath_null) from [<7f22dc70>] (drm_handle_vblank+0x298/0x29c [drm])
[ 45.772718] [<7f22dc70>] (drm_handle_vblank [drm]) from [<7f22dc98>] (drm_crtc_handle_vblank+0x24/0x28 [drm])
[ 45.773035] [<7f22dc98>] (drm_crtc_handle_vblank [drm]) from [<7f4f1158>] (vc4_crtc_irq_handler+0x4c/0x94 [vc4])
[ 45.773130] [<7f4f1158>] (vc4_crtc_irq_handler [vc4]) from [<80173dd8>] (__handle_irq_event_percpu+0xc0/0x22c)
[ 45.773147] [<80173dd8>] (__handle_irq_event_percpu) from [<80173f70>] (handle_irq_event_percpu+0x2c/0x68)
[ 45.773160] [<80173f70>] (handle_irq_event_percpu) from [<80174000>] (handle_irq_event+0x54/0x78)
[ 45.773175] [<80174000>] (handle_irq_event) from [<80177718>] (handle_level_irq+0xb0/0x158)
[ 45.773189] [<80177718>] (handle_level_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.773207] [<80172ecc>] (generic_handle_irq) from [<8047d9e8>] (bcm2836_chained_handle_irq+0x38/0x50)
[ 45.773223] [<8047d9e8>] (bcm2836_chained_handle_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.773235] [<80172ecc>] (generic_handle_irq) from [<8017350c>] (__handle_domain_irq+0x6c/0xc4)
[ 45.773250] [<8017350c>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 45.773268] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<8071893c>] (__irq_svc+0x5c/0x7c)
[ 45.773275] Exception stack(0x80c01e10 to 0x80c01e58)
[ 45.773284] 1e00: ffff9cb1 00000000 80c7a980 00000000
[ 45.773295] 1e20: 80c0209c 00000006 80c00020 00000100 b6005180 00000018 00000040 80c01ec4
[ 45.773305] 1e40: 80c040a4 80c01e60 80101600 80101604 60000113 ffffffff
[ 45.773321] [<8071893c>] (__irq_svc) from [<80101604>] (__do_softirq+0xf4/0x3cc)
[ 45.773335] [<80101604>] (__do_softirq) from [<80122c04>] (irq_exit+0x10c/0x168)
[ 45.773348] [<80122c04>] (irq_exit) from [<80173510>] (__handle_domain_irq+0x70/0xc4)
[ 45.773361] [<80173510>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 45.773374] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<8071893c>] (__irq_svc+0x5c/0x7c)
[ 45.773380] Exception stack(0x80c01f18 to 0x80c01f60)
[ 45.773387] 1f00: 00000000 b6798478
[ 45.773398] 1f20: 00000000 00000000 80c00000 80c0312c 00000001 80c03198 80c15e86 80c15e86
[ 45.773411] 1f40: b6fff980 80c01f74 80c040a4 80c01f68 80108a54 80108a58 60000013 ffffffff
[ 45.773427] [<8071893c>] (__irq_svc) from [<80108a58>] (arch_cpu_idle+0x34/0x4c)
[ 45.773442] [<80108a58>] (arch_cpu_idle) from [<80718094>] (default_idle_call+0x34/0x48)
[ 45.773457] [<80718094>] (default_idle_call) from [<80161c3c>] (cpu_startup_entry+0xe4/0x160)
[ 45.773475] [<80161c3c>] (cpu_startup_entry) from [<80712920>] (rest_init+0x84/0x88)
[ 45.773495] [<80712920>] (rest_init) from [<80b00d28>] (start_kernel+0x3b4/0x3c0)
[ 45.773502] ---[ end trace fb713ce1354546ba ]---
[ 45.782307] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 45.789438] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 45.789448] [drm] Driver supports precise vblank timestamp query.
[ 45.805129] Console: switching to colour frame buffer device 100x30
[ 45.814708] vc4-drm soc:gpu: fb0: frame buffer device
[ 46.032533] uart-pl011 3f201000.serial: no DMA platform data
[ 46.398629] Bluetooth: Core ver 2.22
[ 46.398712] NET: Registered protocol family 31
[ 46.398718] Bluetooth: HCI device and connection manager initialized
[ 46.398743] Bluetooth: HCI socket layer initialized
[ 46.398759] Bluetooth: L2CAP socket layer initialized
[ 46.398797] Bluetooth: SCO socket layer initialized
[ 46.483085] brcmfmac: power management disabled
[ 47.318061] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 47.318082] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 47.497220] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 47.518165] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 48.875027] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 48.875042] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 49.105275] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 50.044718] brcmfmac: power management disabled
[ 50.591298] Bluetooth: HCI UART driver ver 2.3
[ 50.591309] Bluetooth: HCI UART protocol H4 registered
[ 50.591311] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 50.591449] Bluetooth: HCI UART protocol Broadcom registered
[ 50.635550] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 50.635581] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 50.877411] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 50.877420] Bluetooth: BNEP filters: protocol multicast
[ 50.877439] Bluetooth: BNEP socket layer initialized
[ 51.000666] Bluetooth: RFCOMM TTY layer initialized
[ 51.000694] Bluetooth: RFCOMM socket layer initialized
[ 51.000715] Bluetooth: RFCOMM ver 1.11
[ 51.781886] brcmfmac: power management disabled
[ 52.188962] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 52.577953] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 56.651106] systemd[1]: apt-daily.timer: Adding 43min 39.536466s random time.
[ 56.675424] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 60.288546] fuse init (API version 7.26)
With vc4-fkms-v3d enabled, v3d_freq=300:
Code: Select all
dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
dtparam=sd_overclock=63
#dtparam=audio=on
#audio_pwm_mode=1
#audio_pwm_mode=2
dtoverlay=audioinjector-addons
enable_uart=1
lcd_rotate=2
ignore_lcd=0
#total_mem=1024
#gpu_mem=32
gpu_mem=128
#dtoverlay=vc4-kms-v3d,cma-256,rpi-ft5406
dtoverlay=vc4-fkms-v3d,cma-192,rpi-ft5406
#dtoverlay=rpi-ft5406
arm_freq=1200
arm_freq_min=600
core_freq=250
core_freq_min=250
h264_freq=300
isp_freq=250
v3d_freq=300
avoid_pwm_pll=1
#sdram_freq=450
#sdram_schmoo=0x02000020
#over_voltage=2
#over_voltage_sdram=2
decode_MPG2=0x3ab16f03
decode_WVC1=0x438a78fbCode: Select all
pi@raspberrypi:~$ vcgencmd get_throttled
throttled=0x0Code: Select all
[ 4.906568] cs42xx8 1-0048: found device, revision 4
[ 4.954055] usbcore: registered new interface driver brcmfmac
[ 5.162997] brcmfmac: Firmware version = wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[ 5.953646] brcmfmac: power management disabled
[ 6.176053] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 6.176073] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 6.185599] vc4-drm soc:gpu: bound 3f600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 6.198411] ------------[ cut here ]------------
[ 6.198736] WARNING: CPU: 0 PID: 411 at drivers/gpu/drm/drm_irq.c:1794 drm_handle_vblank+0x298/0x29c [drm]
[ 6.198743] Modules linked in: binfmt_misc brcmfmac snd_soc_cs42xx8_i2c snd_soc_cs42xx8 brcmutil evdev cfg80211 joydev rfkill spidev vc4(+) drm_kms_helper drm snd_soc_bcm2835_i2s snd_soc_audioinjector_octo_soundcard syscopyarea sysfillrect snd_soc_core sysimgblt fb_sys_fops snd_compress snd_pcm_dmaengine snd_pcm_oss snd_mixer_oss i2c_bcm2835 snd_pcm snd_timer snd spi_bcm2835 bcm2835_gpiomem cdc_acm rpi_ft5406 rpi_backlight uio_pdrv_genirq fixed uio i2c_dev ip_tables x_tables ipv6
[ 6.198918] CPU: 0 PID: 411 Comm: mv Not tainted 4.9.24-v7+ #993
[ 6.198922] Hardware name: BCM2835
[ 6.198966] [<8010fb3c>] (unwind_backtrace) from [<8010c058>] (show_stack+0x20/0x24)
[ 6.198986] [<8010c058>] (show_stack) from [<80455200>] (dump_stack+0xd4/0x118)
[ 6.199005] [<80455200>] (dump_stack) from [<8011d2c4>] (__warn+0xf8/0x110)
[ 6.199019] [<8011d2c4>] (__warn) from [<8011d3ac>] (warn_slowpath_null+0x30/0x38)
[ 6.199276] [<8011d3ac>] (warn_slowpath_null) from [<7f269c70>] (drm_handle_vblank+0x298/0x29c [drm])
[ 6.199772] [<7f269c70>] (drm_handle_vblank [drm]) from [<7f269c98>] (drm_crtc_handle_vblank+0x24/0x28 [drm])
[ 6.200085] [<7f269c98>] (drm_crtc_handle_vblank [drm]) from [<7f323158>] (vc4_crtc_irq_handler+0x4c/0x94 [vc4])
[ 6.200178] [<7f323158>] (vc4_crtc_irq_handler [vc4]) from [<80173dd8>] (__handle_irq_event_percpu+0xc0/0x22c)
[ 6.200194] [<80173dd8>] (__handle_irq_event_percpu) from [<80173f70>] (handle_irq_event_percpu+0x2c/0x68)
[ 6.200207] [<80173f70>] (handle_irq_event_percpu) from [<80174000>] (handle_irq_event+0x54/0x78)
[ 6.200223] [<80174000>] (handle_irq_event) from [<80177718>] (handle_level_irq+0xb0/0x158)
[ 6.200238] [<80177718>] (handle_level_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 6.200254] [<80172ecc>] (generic_handle_irq) from [<8047d9e8>] (bcm2836_chained_handle_irq+0x38/0x50)
[ 6.200271] [<8047d9e8>] (bcm2836_chained_handle_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 6.200283] [<80172ecc>] (generic_handle_irq) from [<8017350c>] (__handle_domain_irq+0x6c/0xc4)
[ 6.200299] [<8017350c>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 6.200319] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<80718c8c>] (__irq_usr+0x4c/0x60)
[ 6.200325] Exception stack(0xb2705fb0 to 0xb2705ff8)
[ 6.200335] 5fa0: 7edd6b22 00000000 00000000 7edd6b2d
[ 6.200346] 5fc0: 00000005 00000001 0000000a 76f7d218 00000010 7edd6b80 7edd6b18 7edd6b7c
[ 6.200356] 5fe0: 00000000 7edd6b18 76f5ef30 76f696f0 60000010 ffffffff
[ 6.200366] ---[ end trace a9e0c544a0e284a9 ]---
[ 6.208081] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 6.211840] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 6.211849] [drm] Driver supports precise vblank timestamp query.
[ 6.232096] Console: switching to colour frame buffer device 100x30
[ 6.240612] vc4-drm soc:gpu: fb0: frame buffer device
[ 7.176209] uart-pl011 3f201000.serial: no DMA platform data
[ 7.398295] Bluetooth: Core ver 2.22
[ 7.398377] NET: Registered protocol family 31
[ 7.398383] Bluetooth: HCI device and connection manager initialized
[ 7.398408] Bluetooth: HCI socket layer initialized
[ 7.398423] Bluetooth: L2CAP socket layer initialized
[ 7.398456] Bluetooth: SCO socket layer initialized
[ 7.469228] random: crng init done
[ 7.751256] audioinjector-octo soc:sound: cs42448 <-> 3f203000.i2s mapping ok
[ 8.498696] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 8.678347] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 10.162522] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 11.687525] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 11.716871] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 11.720638] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 11.730766] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 11.750177] brcmfmac: power management disabled
[ 12.246172] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 12.246195] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 13.263689] Bluetooth: HCI UART driver ver 2.3
[ 13.263698] Bluetooth: HCI UART protocol H4 registered
[ 13.263700] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 13.263824] Bluetooth: HCI UART protocol Broadcom registered
[ 13.473166] brcmfmac: power management disabled
[ 13.602278] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.602287] Bluetooth: BNEP filters: protocol multicast
[ 13.602305] Bluetooth: BNEP socket layer initialized
[ 13.930017] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 13.983609] Bluetooth: RFCOMM TTY layer initialized
[ 13.983638] Bluetooth: RFCOMM socket layer initialized
[ 13.983658] Bluetooth: RFCOMM ver 1.11
[ 14.365670] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 18.807799] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 20.727894] fuse init (API version 7.26)
[ 22.483094] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
[ 33.337171] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 33.367133] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 33.370868] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 33.377476] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 38.530937] bcm2835-dma 3f007000.dma: DMA transfer could not be terminatedThe MoPower UPS was really designed with the power requirements of the Pi2B (before the release of the Pi3B and its higher power usage). I use a nice powered USB hub for everything other than the touchscreen, Pi3B, Octo and MoPower UPS. It's possible I've just reached the limits of what the MoPower UPS can reliably do.
Re: Octo arrived and working, potentiometer knobs?
Are you using any of the GPIOs which are also used by the Octo ? Particularly gpio05 ?
This post lists the pins in use :
viewtopic.php?f=9&t=1317
Alternatively this problem may be due to something more drastic, which is putting the codec into a funny state due to power fluctuations or switch mode surges or something else power related. The Octo uses a reset pin to manage these sorts of problems, by resetting the Octo before setting it up. Perhaps if the Octo is reset and setup after everything else has settled, it will behave the way it should.
Do you know if the overlay loading is sequential according to the listing order in the /boot/config.txt file ?
If it is sequential, can you put the octo overlay after your other overlays ? Does that change anything ?
thanks
Matt
This post lists the pins in use :
viewtopic.php?f=9&t=1317
Alternatively this problem may be due to something more drastic, which is putting the codec into a funny state due to power fluctuations or switch mode surges or something else power related. The Octo uses a reset pin to manage these sorts of problems, by resetting the Octo before setting it up. Perhaps if the Octo is reset and setup after everything else has settled, it will behave the way it should.
Do you know if the overlay loading is sequential according to the listing order in the /boot/config.txt file ?
If it is sequential, can you put the octo overlay after your other overlays ? Does that change anything ?
thanks
Matt
Check out our audiophile quality crossovers : https://bit.ly/2kb1nzZ
Please review the Zero sound card on Amazon USA : https://www.amazon.com/dp/B075V1VNDD
---
Check out our new forum on github : https://github.com/Audio-Injector
Please review the Zero sound card on Amazon USA : https://www.amazon.com/dp/B075V1VNDD
---
Check out our new forum on github : https://github.com/Audio-Injector
Re: Octo arrived and working, potentiometer knobs?
The MoPower UPS hooks up to pins 2,4,6,8 and 10:
5v, 5v, Ground, GPIO14, GPIO15.
http://www.allspectrum.com/mopower/MoPo ... 0-2017.pdf
The touchscreen uses a DSI ribbon cable (but I believe it actually uses the i2c-0 bus behind the scenes) as well as 5v and Ground pins on the MoPower UPS.
I'm not using any other GPIO.
I don't know about the details of dtoverlay loading order. There are some interesting details here -- https://github.com/raspberrypi/document ... 54-caveats, but nothing I see that would indicate exactly how that works. I do believe some overlays can be applied after booting using the dtoverlay command -- https://github.com/raspberrypi/document ... ay-command. Whether or not that would work for the Octo overlay, I have no idea. So, I will try moving the dtoverlay=audioinjector-addons to the end of config.txt, but I also think I'll try loading it using rc.local or just manually after the system finishes booting. Thank you for the idea.
UPDATE: Unfortunately, the order of dtoverlays specified in config.txt seems to make no difference. Also, attempting to load the audioinjector-addons overlay after the system has finished booting seems to fail every time I try. I tried adding and removing the overlay a handful of times:
I wonder if this information from the Caveats-section in the above linked Device Tree documentation explains some of this:
5v, 5v, Ground, GPIO14, GPIO15.
http://www.allspectrum.com/mopower/MoPo ... 0-2017.pdf
The touchscreen uses a DSI ribbon cable (but I believe it actually uses the i2c-0 bus behind the scenes) as well as 5v and Ground pins on the MoPower UPS.
I'm not using any other GPIO.
I don't know about the details of dtoverlay loading order. There are some interesting details here -- https://github.com/raspberrypi/document ... 54-caveats, but nothing I see that would indicate exactly how that works. I do believe some overlays can be applied after booting using the dtoverlay command -- https://github.com/raspberrypi/document ... ay-command. Whether or not that would work for the Octo overlay, I have no idea. So, I will try moving the dtoverlay=audioinjector-addons to the end of config.txt, but I also think I'll try loading it using rc.local or just manually after the system finishes booting. Thank you for the idea.
UPDATE: Unfortunately, the order of dtoverlays specified in config.txt seems to make no difference. Also, attempting to load the audioinjector-addons overlay after the system has finished booting seems to fail every time I try. I tried adding and removing the overlay a handful of times:
Code: Select all
pi@raspberrypi:~$ sudo dtoverlay audioinjector-addonsCode: Select all
pi@raspberrypi:~$ sudo dtoverlay -r audioinjector-addonsCode: Select all
[ 441.409476] i2c i2c-1: of_i2c: invalid reg on /soc/i2c@7e804000/codec-mclk
[ 441.409485] i2c i2c-1: failed to create client for '/soc/i2c@7e804000/codec-mclk'
[ 441.409489] OF: changeset notifier error @/soc/i2c@7e804000/codec-mclk
[ 441.442520] cs42xx8 1-0048: failed to get the clock: -517
[ 441.442616] cs42xx8: probe of 1-0048 failed with error -22
[ 442.980424] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 442.980436] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 617.771941] brcmfmac: send_key_to_dongle: wsec_key error (-110)
[ 631.452986] cs42xx8 1-0048: failed to get the clock: -517
[ 631.453051] cs42xx8: probe of 1-0048 failed with error -22
[ 631.453072] i2c i2c-1: of_i2c: invalid reg on /soc/i2c@7e804000/codec-mclk
[ 631.453077] i2c i2c-1: failed to create client for '/soc/i2c@7e804000/codec-mclk'
[ 631.453080] OF: changeset notifier error @/soc/i2c@7e804000/codec-mclk
[ 633.012073] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 633.012087] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 706.499657] cs42xx8 1-0048: failed to get the clock: -517
[ 706.499724] cs42xx8: probe of 1-0048 failed with error -22
[ 706.499746] i2c i2c-1: of_i2c: invalid reg on /soc/i2c@7e804000/codec-mclk
[ 706.499751] i2c i2c-1: failed to create client for '/soc/i2c@7e804000/codec-mclk'
[ 706.499753] OF: changeset notifier error @/soc/i2c@7e804000/codec-mclk
[ 708.052811] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 708.052826] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 787.884156] cs42xx8 1-0048: failed to get the clock: -517
[ 787.884224] cs42xx8: probe of 1-0048 failed with error -22
[ 787.884246] i2c i2c-1: of_i2c: invalid reg on /soc/i2c@7e804000/codec-mclk
[ 787.884251] i2c i2c-1: failed to create client for '/soc/i2c@7e804000/codec-mclk'
[ 787.884253] OF: changeset notifier error @/soc/i2c@7e804000/codec-mclk
[ 789.443437] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 789.443450] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)Adding clocks under the /clocks node at run-time doesn't cause a new clock provider to be registered, so devm_clk_get will fail for a clock created in an overlay.
Re: Octo arrived and working, potentiometer knobs?
After my attempts to manually load the audioinjector-addons overlay, I rebooted the system and just left it for a long time. When I came back, I noticed the local keyboard connected to the Pi3B through a hub wasn't working. The mouse still worked. I SSHed in and found what looks like a new kernel panic or VC4 error which I haven't seen before. On the next four reboots, the Audio Injector Octo failed to load. On the fifth reboot, the Octo loaded and worked.
Next I tried powering the touchscreen with a separate power supply via micro USB. If these problems are caused by an insufficient power supply, I would expect that only running the Pi3B and Octo from the MoPower UPS should avoid the problems. Unfortunately, the same problems occur. I suppose the only things left to check are whether or not completely removing the MoPower UPS from my setup solves my problems or if not using the vc4-fkms-v3d overlay and/or touchscreen solves anything. I don't think the Octo uses much more power than a keyboard or mouse based on the requested power information you posted on the kickstarter site.
UPDATE: Not using the vc4-fkms-v3d overlay doesn't appear to really solve anything. The Octo still failed to load intermittently on 3 out of 5 reboot attempts.
UPDATE 2: Going further, I commented out the rpi-ft5406 (touchscreen) overlay and set ignore_lcd=1 in config.txt and booted up with an HDMI screen connected instead. The first reboot worked (I had sound), but I could see that the first load attempt of the Octo still failed, while the second attempt apparently worked.
The next reboot attempt was a failure. No sound.
Third and fourth reboots, the Octo loaded OK and there was sound.
The fifth reboot was another failure, no sound:
I think I've had my fill of this mess for now. Next I'll probably try disassembling everything and running the Octo with only my Pi3B + HDMI. Perhaps I'll try the Octo with my Pi2B as well. Then I'll try a fresh copy of Raspbian Jessie. Ughghghg...
Code: Select all
On reboot after my attempts to manually load the audioinjector-addons overlay
--------------------------------------------------------------------------------
[ 44.175928] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 44.176279] cs42xx8: probe of 1-0048 failed with error -121
[ 45.135587] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 45.135608] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 45.155525] vc4-drm soc:gpu: bound 3f600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 45.158089] ------------[ cut here ]------------
[ 45.158467] WARNING: CPU: 0 PID: 216 at drivers/gpu/drm/drm_irq.c:1794 drm_handle_vblank+0x298/0x29c [drm]
[ 45.158477] Modules linked in: binfmt_misc snd_soc_cs42xx8_i2c snd_soc_cs42xx8 joydev spidev vc4(+) brcmfmac drm_kms_helper brcmutil drm snd_soc_audioinjector_octo_soundcard snd_soc_bcm2835_i2s cfg80211 snd_soc_core snd_compress snd_pcm_dmaengine syscopyarea sysfillrect rfkill snd_pcm_oss sysimgblt snd_mixer_oss fb_sys_fops snd_pcm snd_timer i2c_bcm2835 snd spi_bcm2835 bcm2835_gpiomem rpi_ft5406 fixed rpi_backlight uio_pdrv_genirq uio evdev cdc_acm i2c_dev ip_tables x_tables ipv6
[ 45.158699] CPU: 0 PID: 216 Comm: systemd-udevd Not tainted 4.9.24-v7+ #993
[ 45.158708] Hardware name: BCM2835
[ 45.158749] [<8010fb3c>] (unwind_backtrace) from [<8010c058>] (show_stack+0x20/0x24)
[ 45.158784] [<8010c058>] (show_stack) from [<80455200>] (dump_stack+0xd4/0x118)
[ 45.158815] [<80455200>] (dump_stack) from [<8011d2c4>] (__warn+0xf8/0x110)
[ 45.158841] [<8011d2c4>] (__warn) from [<8011d3ac>] (warn_slowpath_null+0x30/0x38)
[ 45.159217] [<8011d3ac>] (warn_slowpath_null) from [<7f3b8c70>] (drm_handle_vblank+0x298/0x29c [drm])
[ 45.159775] [<7f3b8c70>] (drm_handle_vblank [drm]) from [<7f3b8c98>] (drm_crtc_handle_vblank+0x24/0x28 [drm])
[ 45.160092] [<7f3b8c98>] (drm_crtc_handle_vblank [drm]) from [<7f50e158>] (vc4_crtc_irq_handler+0x4c/0x94 [vc4])
[ 45.160232] [<7f50e158>] (vc4_crtc_irq_handler [vc4]) from [<80173dd8>] (__handle_irq_event_percpu+0xc0/0x22c)
[ 45.160264] [<80173dd8>] (__handle_irq_event_percpu) from [<80173f70>] (handle_irq_event_percpu+0x2c/0x68)
[ 45.160288] [<80173f70>] (handle_irq_event_percpu) from [<80174000>] (handle_irq_event+0x54/0x78)
[ 45.160321] [<80174000>] (handle_irq_event) from [<80177718>] (handle_level_irq+0xb0/0x158)
[ 45.160340] [<80177718>] (handle_level_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.160358] [<80172ecc>] (generic_handle_irq) from [<8047d9e8>] (bcm2836_chained_handle_irq+0x38/0x50)
[ 45.160374] [<8047d9e8>] (bcm2836_chained_handle_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.160386] [<80172ecc>] (generic_handle_irq) from [<8017350c>] (__handle_domain_irq+0x6c/0xc4)
[ 45.160401] [<8017350c>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 45.160419] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<8071893c>] (__irq_svc+0x5c/0x7c)
[ 45.160425] Exception stack(0x885cf990 to 0x885cf9d8)
[ 45.160435] f980: 902a8f00 00f57100 00000000 00000000
[ 45.160446] f9a0: 90200000 01000000 00000000 00000647 01000000 00000000 8800ab08 885cfa04
[ 45.160456] f9c0: 00000000 885cf9e4 00000000 80454460 20000113 ffffffff
[ 45.160474] [<8071893c>] (__irq_svc) from [<80454460>] (__memzero+0x20/0x80)
[ 45.160489] [<80454460>] (__memzero) from [<80114910>] (__dma_clear_buffer+0x80/0x8c)
[ 45.160503] [<80114910>] (__dma_clear_buffer) from [<80114b7c>] (__alloc_from_contiguous+0x50/0xc4)
[ 45.160515] [<80114b7c>] (__alloc_from_contiguous) from [<80114c30>] (cma_allocator_alloc+0x40/0x48)
[ 45.160527] [<80114c30>] (cma_allocator_alloc) from [<80114e0c>] (__dma_alloc+0x1d4/0x32c)
[ 45.160538] [<80114e0c>] (__dma_alloc) from [<80114ffc>] (arm_dma_alloc+0x50/0x58)
[ 45.160816] [<80114ffc>] (arm_dma_alloc) from [<7f3d4200>] (drm_gem_cma_create+0xa4/0xf8 [drm])
[ 45.161211] [<7f3d4200>] (drm_gem_cma_create [drm]) from [<7f506500>] (vc4_bo_create+0xdc/0x128 [vc4])
[ 45.161376] [<7f506500>] (vc4_bo_create [vc4]) from [<7f515d04>] (vc4_allocate_bin_bo+0x74/0x140 [vc4])
[ 45.161509] [<7f515d04>] (vc4_allocate_bin_bo [vc4]) from [<7f515eb4>] (vc4_v3d_bind+0x90/0x184 [vc4])
[ 45.161585] [<7f515eb4>] (vc4_v3d_bind [vc4]) from [<804f5174>] (component_bind_all+0x100/0x234)
[ 45.161655] [<804f5174>] (component_bind_all) from [<7f5087b0>] (vc4_drm_bind+0x88/0x13c [vc4])
[ 45.161726] [<7f5087b0>] (vc4_drm_bind [vc4]) from [<804f5614>] (try_to_bring_up_master+0x158/0x198)
[ 45.161743] [<804f5614>] (try_to_bring_up_master) from [<804f5840>] (component_master_add_with_match+0x9c/0xcc)
[ 45.161812] [<804f5840>] (component_master_add_with_match) from [<7f508910>] (vc4_platform_drm_probe+0xac/0xb8 [vc4])
[ 45.161882] [<7f508910>] (vc4_platform_drm_probe [vc4]) from [<804fc2e8>] (platform_drv_probe+0x5c/0xc0)
[ 45.161899] [<804fc2e8>] (platform_drv_probe) from [<804fa890>] (driver_probe_device+0x220/0x2cc)
[ 45.161916] [<804fa890>] (driver_probe_device) from [<804fa9f8>] (__driver_attach+0xbc/0xc0)
[ 45.161932] [<804fa9f8>] (__driver_attach) from [<804f8864>] (bus_for_each_dev+0x7c/0xb0)
[ 45.161948] [<804f8864>] (bus_for_each_dev) from [<804fa210>] (driver_attach+0x2c/0x30)
[ 45.161963] [<804fa210>] (driver_attach) from [<804f9da8>] (bus_add_driver+0x1b4/0x22c)
[ 45.161979] [<804f9da8>] (bus_add_driver) from [<804fb0f0>] (driver_register+0x88/0x108)
[ 45.161994] [<804fb0f0>] (driver_register) from [<804fc238>] (__platform_driver_register+0x50/0x58)
[ 45.162064] [<804fc238>] (__platform_driver_register) from [<7f529068>] (vc4_drm_register+0x68/0x74 [vc4])
[ 45.162161] [<7f529068>] (vc4_drm_register [vc4]) from [<80101bf0>] (do_one_initcall+0x50/0x184)
[ 45.162179] [<80101bf0>] (do_one_initcall) from [<80209a6c>] (do_init_module+0x74/0x1e4)
[ 45.162198] [<80209a6c>] (do_init_module) from [<801a32dc>] (load_module+0x19cc/0x2108)
[ 45.162218] [<801a32dc>] (load_module) from [<801a3bf4>] (SyS_finit_module+0x9c/0xac)
[ 45.162236] [<801a3bf4>] (SyS_finit_module) from [<80108220>] (__sys_trace_return+0x0/0x10)
[ 45.162245] ---[ end trace af02a601543d49e6 ]---
[ 45.183283] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 45.194436] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 45.194448] [drm] Driver supports precise vblank timestamp query.
[ 45.225131] Console: switching to colour frame buffer device 100x30
[ 45.238398] vc4-drm soc:gpu: fb0: frame buffer device
[ 45.278974] uart-pl011 3f201000.serial: no DMA platform data
[ 45.347432] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 45.347447] brcmfmac: power management disabled
[ 45.522978] Bluetooth: Core ver 2.22
[ 45.523053] NET: Registered protocol family 31
[ 45.523059] Bluetooth: HCI device and connection manager initialized
[ 45.523149] Bluetooth: HCI socket layer initialized
[ 45.523164] Bluetooth: L2CAP socket layer initialized
[ 45.523200] Bluetooth: SCO socket layer initialized
[ 46.430348] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 46.695574] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 46.695588] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 48.255548] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 48.255563] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 48.966214] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 49.066804] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 49.092441] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 49.634119] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 49.634130] brcmfmac: power management disabled
[ 49.881495] Bluetooth: HCI UART driver ver 2.3
[ 49.881507] Bluetooth: HCI UART protocol H4 registered
[ 49.881512] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 49.882689] Bluetooth: HCI UART protocol Broadcom registered
[ 50.108942] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 50.108953] Bluetooth: BNEP filters: protocol multicast
[ 50.108969] Bluetooth: BNEP socket layer initialized
[ 50.223087] Bluetooth: RFCOMM TTY layer initialized
[ 50.223120] Bluetooth: RFCOMM socket layer initialized
[ 50.223143] Bluetooth: RFCOMM ver 1.11
[ 50.241780] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 50.241797] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 50.257553] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 50.589321] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 53.125800] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 53.125838] brcmfmac: power management disabled
[ 54.617097] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 54.702657] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 55.130575] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 60.073379] fuse init (API version 7.26)
[ 62.565530] brcmfmac: brcmf_cfg80211_stop_ap: SET SSID error (-110)
[ 65.125474] brcmfmac: brcmf_cfg80211_stop_ap: BRCMF_C_DOWN error -110
[ 67.685480] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -110
[ 70.245478] brcmfmac: brcmf_cfg80211_stop_ap: setting AP mode failed -110
[ 75.365473] brcmfmac: brcmf_cfg80211_stop_ap: BRCMF_C_UP error -110
[ 77.925467] brcmfmac: brcmf_set_mpc: fail to set mpc
[ 657.692800] brcmfmac: send_key_to_dongle: wsec_key error (-110)
[ 1951.800929] vc4-drm soc:gpu: failed to allocate buffer with size 16777216
[ 4231.222981] vc4-drm soc:gpu: failed to allocate buffer with size 16777216
[ 4231.338975] vc4-drm soc:gpu: failed to allocate buffer with size 16777216
[ 4231.339038] [drm:vc4_bo_create [vc4]] *ERROR* Failed to allocate from CMA:
[ 4231.339041] [drm] num bos allocated: 42
[ 4231.339043] [drm] size bos allocated: 27524kb
[ 4231.339045] [drm] num bos used: 42
[ 4231.339048] [drm] size bos used: 27524kb
[ 4231.339051] [drm] num bos cached: 0
[ 4231.339053] [drm] size bos cached: 0kb
[ 4231.339059] vc4_v3d 3fc00000.v3d: Failed to allocate memory for tile binning: -12. You may need to enable CMA or give it more memory.
[ 4231.429681] Unable to handle kernel NULL pointer dereference at virtual address 00000088
[ 4231.429697] pgd = 8834c000
[ 4231.429702] [00000088] *pgd=03c09835, *pte=00000000, *ppte=00000000
[ 4231.429718] Internal error: Oops: 17 [#1] SMP ARM
[ 4231.429725] Modules linked in: fuse ipt_MASQUERADE nf_nat_masquerade_ipv4 xt_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp iptable_filter nf_nat_h323 nf_conntrack_h323 nf_nat_pptp nf_nat_proto_gre nf_conntrack_pptp nf_conntrack_proto_gre nf_nat_tftp nf_conntrack_tftp nf_nat_sip nf_conntrack_sip nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack cmac rfcomm bnep hci_uart btbcm bluetooth binfmt_misc snd_soc_cs42xx8_i2c snd_soc_cs42xx8 joydev spidev vc4 brcmfmac drm_kms_helper brcmutil drm snd_soc_audioinjector_octo_soundcard snd_soc_bcm2835_i2s cfg80211 snd_soc_core snd_compress snd_pcm_dmaengine syscopyarea sysfillrect rfkill snd_pcm_oss sysimgblt snd_mixer_oss fb_sys_fops snd_pcm snd_timer i2c_bcm2835 snd spi_bcm2835
[ 4231.429852] bcm2835_gpiomem rpi_ft5406 fixed rpi_backlight uio_pdrv_genirq uio evdev cdc_acm i2c_dev ip_tables x_tables ipv6
[ 4231.429883] CPU: 1 PID: 887 Comm: Xorg Tainted: G W 4.9.24-v7+ #993
[ 4231.429887] Hardware name: BCM2835
[ 4231.429893] task: 887349c0 task.stack: 883d2000
[ 4231.429937] PC is at validate_tile_binning_config+0xb4/0x19c [vc4]
[ 4231.429948] LR is at _raw_spin_unlock_irqrestore+0x3c/0x70
[ 4231.429955] pc : [<7f516174>] lr : [<80718644>] psr: 60000013
sp : 883d3d28 ip : 00000044 fp : 883d3d64
[ 4231.429962] r10: 00000000 r9 : 00000001 r8 : b5acae10
[ 4231.429967] r7 : 00000000 r6 : 90135001 r5 : 881f0780 r4 : 00000006
[ 4231.429973] r3 : 00080000 r2 : 000000ea r1 : 00000000 r0 : 00000000
[ 4231.429979] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 4231.429986] Control: 10c5383d Table: 0834c06a DAC: 00000055
[ 4231.429991] Process Xorg (pid: 887, stack limit = 0x883d2210)
[ 4231.429997] Stack: (0x883d3d28 to 0x883d4000)
[ 4231.430004] 3d20: 80114ffc 80114c44 00000000 0000000d 00000004 00000070
[ 4231.430013] 3d40: 00000010 7f5160c0 00000010 00000000 7f51ac4c 0000005c 883d3dbc 883d3d68
[ 4231.430024] 3d60: 7f516940 7f5160cc 00001000 00000000 adbf9400 00000001 881f0780 83c68e00
[ 4231.430032] 3d80: 00000000 83c68e00 90135000 7f51e928 83c68ea8 881f0c00 881f0780 83c68e00
[ 4231.430040] 3da0: 881f0180 b5acae10 00000000 00000060 883d3e1c 883d3dc0 7f5103ac 7f516874
[ 4231.430048] 3dc0: 000000a0 883d3dc0 881f0180 000000a0 b5acae10 83c68ea8 881f07c0 adbf9400
[ 4231.430056] 3de0: 0000009c 881f0180 000000a8 7f519034 a3c79200 00000000 881f0180 7f519034
[ 4231.430064] 3e00: a3c79200 000000a0 c0a06440 adbf9400 883d3efc 883d3e20 7f3b6c30 7f50fcb0
[ 4231.430072] 3e20: 0000e200 00000001 7f51bd84 00000054 883d3ea4 883d3e50 7f50fca4 000000a0
[ 4231.430080] 3e40: 00000001 883d3e50 7eb5aab8 00000040 801299a0 801297d8 883d3e84 b59f9a50
[ 4231.430088] 3e60: 00ef4000 00000054 8834c038 b08a33d0 b6eb1708 00000000 883d3ea4 883d3fb0
[ 4231.430096] 3e80: 887349c0 00000017 00ef4fb8 b502b180 b502b1b8 80719258 883d3efc 883d3ea8
[ 4231.430105] 3ea0: 80719258 8016ae88 00002000 00000000 00000000 883d3ec8 883d3f8c 80715ed4
[ 4231.430115] 3ec0: 883d3ee4 00000000 00000000 00000000 883d20f8 7eb5aab8 ada91b48 b51e5f00
[ 4231.430123] 3ee0: c0a06440 0000000d 883d2000 00000000 883d3f7c 883d3f00 802831cc 7f3b6a30
[ 4231.430132] 3f00: 00001fa8 00000000 883d3f34 883d2000 7eb5a4f8 7eb5a3f0 41034034 00000000
[ 4231.430140] 3f20: 883d2000 00000000 883d3f44 883d3f38 80461764 8028f62c ad80d900 01381748
[ 4231.430148] 3f40: 7eb5aab8 c0a06440 c0a06440 0000000d 883d3f6c b51e5f01 7eb5aab8 b51e5f00
[ 4231.430156] 3f60: c0a06440 0000000d 883d2000 00000000 883d3fa4 883d3f80 80283984 8028312c
[ 4231.430164] 3f80: 00000000 01381748 7eb5aab8 c0a06440 00000036 80108244 00000000 883d3fa8
[ 4231.430172] 3fa0: 801080c0 8028394c 01381748 7eb5aab8 0000000d c0a06440 7eb5aab8 00000000
[ 4231.430180] 3fc0: 01381748 7eb5aab8 c0a06440 00000036 7eb5aab8 00000040 00000040 76f67ce8
[ 4231.430188] 3fe0: 76d5008c 7eb5aa8c 76d37950 76a3d6cc 60000010 0000000d 66ac94e2 a4782260
[ 4231.430256] [<7f516174>] (validate_tile_binning_config [vc4]) from [<7f516940>] (vc4_validate_bin_cl+0xd8/0x2e0 [vc4])
[ 4231.430314] [<7f516940>] (vc4_validate_bin_cl [vc4]) from [<7f5103ac>] (vc4_submit_cl_ioctl+0x708/0x938 [vc4])
[ 4231.430489] [<7f5103ac>] (vc4_submit_cl_ioctl [vc4]) from [<7f3b6c30>] (drm_ioctl+0x20c/0x428 [drm])
[ 4231.430613] [<7f3b6c30>] (drm_ioctl [drm]) from [<802831cc>] (do_vfs_ioctl+0xac/0x820)
[ 4231.430625] [<802831cc>] (do_vfs_ioctl) from [<80283984>] (SyS_ioctl+0x44/0x6c)
[ 4231.430639] [<80283984>] (SyS_ioctl) from [<801080c0>] (ret_fast_syscall+0x0/0x1c)
[ 4231.430649] Code: e5981100 e38cc044 e5983104 e0822082 (e5911088)
[ 4231.430658] ---[ end trace af02a601543d49e7 ]---
Reboot attempt 2
--------------------------------------------------------------------------------
[ 4.965496] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 4.965812] cs42xx8: probe of 1-0048 failed with error -121
[ 5.223677] cdc_acm 1-1.3.3:1.0: ttyACM0: USB ACM device
[ 5.224609] usbcore: registered new interface driver cdc_acm
[ 5.224617] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 5.752250] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 5.752274] brcmfmac: power management disabled
[ 5.895232] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 5.895252] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 5.906536] vc4-drm soc:gpu: bound 3f600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 5.917191] ------------[ cut here ]------------
[ 5.917465] WARNING: CPU: 0 PID: 188 at drivers/gpu/drm/drm_irq.c:1794 drm_handle_vblank+0x298/0x29c [drm]
[ 5.917470] Modules linked in: binfmt_misc cdc_acm evdev snd_soc_cs42xx8_i2c snd_soc_cs42xx8 joydev spidev brcmfmac brcmutil cfg80211 vc4(+) drm_kms_helper rfkill drm syscopyarea sysfillrect sysimgblt fb_sys_fops snd_soc_bcm2835_i2s snd_soc_audioinjector_octo_soundcard snd_soc_core snd_compress snd_pcm_dmaengine i2c_bcm2835 snd_pcm_oss snd_mixer_oss snd_pcm snd_timer snd bcm2835_gpiomem spi_bcm2835 rpi_ft5406 rpi_backlight uio_pdrv_genirq uio fixed i2c_dev ip_tables x_tables ipv6
[ 5.917628] CPU: 0 PID: 188 Comm: systemd-udevd Not tainted 4.9.24-v7+ #993
[ 5.917633] Hardware name: BCM2835
[ 5.917661] [<8010fb3c>] (unwind_backtrace) from [<8010c058>] (show_stack+0x20/0x24)
[ 5.917678] [<8010c058>] (show_stack) from [<80455200>] (dump_stack+0xd4/0x118)
[ 5.917694] [<80455200>] (dump_stack) from [<8011d2c4>] (__warn+0xf8/0x110)
[ 5.917707] [<8011d2c4>] (__warn) from [<8011d3ac>] (warn_slowpath_null+0x30/0x38)
[ 5.917941] [<8011d3ac>] (warn_slowpath_null) from [<7f1fdc70>] (drm_handle_vblank+0x298/0x29c [drm])
[ 5.918406] [<7f1fdc70>] (drm_handle_vblank [drm]) from [<7f1fdc98>] (drm_crtc_handle_vblank+0x24/0x28 [drm])
[ 5.918705] [<7f1fdc98>] (drm_crtc_handle_vblank [drm]) from [<7f2cd158>] (vc4_crtc_irq_handler+0x4c/0x94 [vc4])
[ 5.918785] [<7f2cd158>] (vc4_crtc_irq_handler [vc4]) from [<80173dd8>] (__handle_irq_event_percpu+0xc0/0x22c)
[ 5.918800] [<80173dd8>] (__handle_irq_event_percpu) from [<80173f70>] (handle_irq_event_percpu+0x2c/0x68)
[ 5.918813] [<80173f70>] (handle_irq_event_percpu) from [<80174000>] (handle_irq_event+0x54/0x78)
[ 5.918827] [<80174000>] (handle_irq_event) from [<80177718>] (handle_level_irq+0xb0/0x158)
[ 5.918841] [<80177718>] (handle_level_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 5.918857] [<80172ecc>] (generic_handle_irq) from [<8047d9e8>] (bcm2836_chained_handle_irq+0x38/0x50)
[ 5.918872] [<8047d9e8>] (bcm2836_chained_handle_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 5.918884] [<80172ecc>] (generic_handle_irq) from [<8017350c>] (__handle_domain_irq+0x6c/0xc4)
[ 5.918898] [<8017350c>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 5.918915] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<8071893c>] (__irq_svc+0x5c/0x7c)
[ 5.918921] Exception stack(0xb5347990 to 0xb53479d8)
[ 5.918930] 7980: 90820e00 009df200 00000000 00000000
[ 5.918942] 79a0: 90200000 01000000 00000000 00000647 01000000 00000000 b254ca48 b5347a04
[ 5.918951] 79c0: 00000000 b53479e4 00000000 80454474 20000013 ffffffff
[ 5.918967] [<8071893c>] (__irq_svc) from [<80454474>] (__memzero+0x34/0x80)
[ 5.918981] [<80454474>] (__memzero) from [<80114910>] (__dma_clear_buffer+0x80/0x8c)
[ 5.918994] [<80114910>] (__dma_clear_buffer) from [<80114b7c>] (__alloc_from_contiguous+0x50/0xc4)
[ 5.919007] [<80114b7c>] (__alloc_from_contiguous) from [<80114c30>] (cma_allocator_alloc+0x40/0x48)
[ 5.919018] [<80114c30>] (cma_allocator_alloc) from [<80114e0c>] (__dma_alloc+0x1d4/0x32c)
[ 5.919030] [<80114e0c>] (__dma_alloc) from [<80114ffc>] (arm_dma_alloc+0x50/0x58)
[ 5.919259] [<80114ffc>] (arm_dma_alloc) from [<7f219200>] (drm_gem_cma_create+0xa4/0xf8 [drm])
[ 5.919547] [<7f219200>] (drm_gem_cma_create [drm]) from [<7f2c5500>] (vc4_bo_create+0xdc/0x128 [vc4])
[ 5.919672] [<7f2c5500>] (vc4_bo_create [vc4]) from [<7f2d4d04>] (vc4_allocate_bin_bo+0x74/0x140 [vc4])
[ 5.919798] [<7f2d4d04>] (vc4_allocate_bin_bo [vc4]) from [<7f2d4eb4>] (vc4_v3d_bind+0x90/0x184 [vc4])
[ 5.919870] [<7f2d4eb4>] (vc4_v3d_bind [vc4]) from [<804f5174>] (component_bind_all+0x100/0x234)
[ 5.919939] [<804f5174>] (component_bind_all) from [<7f2c77b0>] (vc4_drm_bind+0x88/0x13c [vc4])
[ 5.920009] [<7f2c77b0>] (vc4_drm_bind [vc4]) from [<804f5614>] (try_to_bring_up_master+0x158/0x198)
[ 5.920023] [<804f5614>] (try_to_bring_up_master) from [<804f5840>] (component_master_add_with_match+0x9c/0xcc)
[ 5.920091] [<804f5840>] (component_master_add_with_match) from [<7f2c7910>] (vc4_platform_drm_probe+0xac/0xb8 [vc4])
[ 5.920161] [<7f2c7910>] (vc4_platform_drm_probe [vc4]) from [<804fc2e8>] (platform_drv_probe+0x5c/0xc0)
[ 5.920178] [<804fc2e8>] (platform_drv_probe) from [<804fa890>] (driver_probe_device+0x220/0x2cc)
[ 5.920195] [<804fa890>] (driver_probe_device) from [<804fa9f8>] (__driver_attach+0xbc/0xc0)
[ 5.920210] [<804fa9f8>] (__driver_attach) from [<804f8864>] (bus_for_each_dev+0x7c/0xb0)
[ 5.920226] [<804f8864>] (bus_for_each_dev) from [<804fa210>] (driver_attach+0x2c/0x30)
[ 5.920241] [<804fa210>] (driver_attach) from [<804f9da8>] (bus_add_driver+0x1b4/0x22c)
[ 5.920257] [<804f9da8>] (bus_add_driver) from [<804fb0f0>] (driver_register+0x88/0x108)
[ 5.920272] [<804fb0f0>] (driver_register) from [<804fc238>] (__platform_driver_register+0x50/0x58)
[ 5.920342] [<804fc238>] (__platform_driver_register) from [<7f2e8068>] (vc4_drm_register+0x68/0x74 [vc4])
[ 5.920416] [<7f2e8068>] (vc4_drm_register [vc4]) from [<80101bf0>] (do_one_initcall+0x50/0x184)
[ 5.920432] [<80101bf0>] (do_one_initcall) from [<80209a6c>] (do_init_module+0x74/0x1e4)
[ 5.920450] [<80209a6c>] (do_init_module) from [<801a32dc>] (load_module+0x19cc/0x2108)
[ 5.920469] [<801a32dc>] (load_module) from [<801a3bf4>] (SyS_finit_module+0x9c/0xac)
[ 5.920486] [<801a3bf4>] (SyS_finit_module) from [<80108220>] (__sys_trace_return+0x0/0x10)
[ 5.920493] ---[ end trace dfb1086632bbbd96 ]---
[ 5.933281] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 5.934488] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 5.934496] [drm] Driver supports precise vblank timestamp query.
[ 5.950826] Console: switching to colour frame buffer device 100x30
[ 5.960435] vc4-drm soc:gpu: fb0: frame buffer device
[ 7.330884] uart-pl011 3f201000.serial: no DMA platform data
[ 7.408249] random: crng init done
[ 7.438749] Bluetooth: Core ver 2.22
[ 7.438890] NET: Registered protocol family 31
[ 7.438896] Bluetooth: HCI device and connection manager initialized
[ 7.438930] Bluetooth: HCI socket layer initialized
[ 7.438950] Bluetooth: L2CAP socket layer initialized
[ 7.438988] Bluetooth: SCO socket layer initialized
[ 7.455230] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 7.455249] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 8.453087] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 9.015226] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 9.015239] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 9.131914] systemd[1]: Started ACPI event daemon.
[ 10.853428] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.936740] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 10.964113] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 11.493869] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 11.493881] brcmfmac: power management disabled
[ 12.516284] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 12.650907] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 12.650923] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 12.663376] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.828377] Bluetooth: HCI UART driver ver 2.3
[ 12.828385] Bluetooth: HCI UART protocol H4 registered
[ 12.828388] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 12.828526] Bluetooth: HCI UART protocol Broadcom registered
[ 13.158526] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.158537] Bluetooth: BNEP filters: protocol multicast
[ 13.158555] Bluetooth: BNEP socket layer initialized
[ 13.460805] Bluetooth: RFCOMM TTY layer initialized
[ 13.460833] Bluetooth: RFCOMM socket layer initialized
[ 13.460850] Bluetooth: RFCOMM ver 1.11
[ 13.875986] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 13.875996] brcmfmac: power management disabled
[ 15.227697] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 15.233184] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 15.597867] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 15.714450] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 21.431388] fuse init (API version 7.26)
[ 21.525213] brcmfmac: brcmf_cfg80211_stop_ap: SET SSID error (-110)
[ 24.085262] brcmfmac: brcmf_cfg80211_stop_ap: BRCMF_C_DOWN error -110
[ 26.645241] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -110
[ 29.205269] brcmfmac: brcmf_cfg80211_stop_ap: setting AP mode failed -110
[ 34.325347] brcmfmac: brcmf_cfg80211_stop_ap: BRCMF_C_UP error -110
[ 36.885334] brcmfmac: brcmf_set_mpc: fail to set mpc
Reboot attempt 3
--------------------------------------------------------------------------------
[ 4.876054] brcmfmac: Firmware version = wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[ 5.005596] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 5.005966] cs42xx8: probe of 1-0048 failed with error -121
[ 5.217546] cdc_acm 1-1.3.3:1.0: ttyACM0: USB ACM device
[ 5.218710] usbcore: registered new interface driver cdc_acm
[ 5.218719] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 5.914716] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 5.914731] brcmfmac: power management disabled
[ 6.025323] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 6.025342] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 6.032943] vc4-drm soc:gpu: bound 3f600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 6.034546] ------------[ cut here ]------------
[ 6.034842] WARNING: CPU: 0 PID: 0 at drivers/gpu/drm/drm_irq.c:1794 drm_handle_vblank+0x298/0x29c [drm]
[ 6.034851] Modules linked in: binfmt_misc cdc_acm snd_soc_cs42xx8_i2c snd_soc_cs42xx8 evdev joydev spidev brcmfmac brcmutil cfg80211 vc4(+) drm_kms_helper rfkill drm snd_soc_bcm2835_i2s snd_soc_audioinjector_octo_soundcard syscopyarea snd_soc_core sysfillrect sysimgblt snd_compress fb_sys_fops snd_pcm_dmaengine snd_pcm_oss snd_mixer_oss snd_pcm snd_timer spi_bcm2835 i2c_bcm2835 snd bcm2835_gpiomem rpi_backlight uio_pdrv_genirq rpi_ft5406 uio fixed i2c_dev ip_tables x_tables ipv6
[ 6.035025] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.24-v7+ #993
[ 6.035030] Hardware name: BCM2835
[ 6.035069] [<8010fb3c>] (unwind_backtrace) from [<8010c058>] (show_stack+0x20/0x24)
[ 6.035088] [<8010c058>] (show_stack) from [<80455200>] (dump_stack+0xd4/0x118)
[ 6.035107] [<80455200>] (dump_stack) from [<8011d2c4>] (__warn+0xf8/0x110)
[ 6.035122] [<8011d2c4>] (__warn) from [<8011d3ac>] (warn_slowpath_null+0x30/0x38)
[ 6.035438] [<8011d3ac>] (warn_slowpath_null) from [<7f28ec70>] (drm_handle_vblank+0x298/0x29c [drm])
[ 6.035976] [<7f28ec70>] (drm_handle_vblank [drm]) from [<7f28ec98>] (drm_crtc_handle_vblank+0x24/0x28 [drm])
[ 6.036314] [<7f28ec98>] (drm_crtc_handle_vblank [drm]) from [<7f35e158>] (vc4_crtc_irq_handler+0x4c/0x94 [vc4])
[ 6.036446] [<7f35e158>] (vc4_crtc_irq_handler [vc4]) from [<80173dd8>] (__handle_irq_event_percpu+0xc0/0x22c)
[ 6.036465] [<80173dd8>] (__handle_irq_event_percpu) from [<80173f70>] (handle_irq_event_percpu+0x2c/0x68)
[ 6.036478] [<80173f70>] (handle_irq_event_percpu) from [<80174000>] (handle_irq_event+0x54/0x78)
[ 6.036494] [<80174000>] (handle_irq_event) from [<80177718>] (handle_level_irq+0xb0/0x158)
[ 6.036510] [<80177718>] (handle_level_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 6.036528] [<80172ecc>] (generic_handle_irq) from [<8047d9e8>] (bcm2836_chained_handle_irq+0x38/0x50)
[ 6.036548] [<8047d9e8>] (bcm2836_chained_handle_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 6.036560] [<80172ecc>] (generic_handle_irq) from [<8017350c>] (__handle_domain_irq+0x6c/0xc4)
[ 6.036577] [<8017350c>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 6.036600] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<8071893c>] (__irq_svc+0x5c/0x7c)
[ 6.036608] Exception stack(0x80c01f18 to 0x80c01f60)
[ 6.036616] 1f00: 00000000 b6798478
[ 6.036628] 1f20: 00000000 00000000 80c00000 80c0312c 00000001 80c03198 80c15e86 80c15e86
[ 6.036641] 1f40: b6fff9c0 80c01f74 80c040a4 80c01f68 80108a54 80108a58 60000013 ffffffff
[ 6.036662] [<8071893c>] (__irq_svc) from [<80108a58>] (arch_cpu_idle+0x34/0x4c)
[ 6.036679] [<80108a58>] (arch_cpu_idle) from [<80718094>] (default_idle_call+0x34/0x48)
[ 6.036695] [<80718094>] (default_idle_call) from [<80161c3c>] (cpu_startup_entry+0xe4/0x160)
[ 6.036719] [<80161c3c>] (cpu_startup_entry) from [<80712920>] (rest_init+0x84/0x88)
[ 6.036744] [<80712920>] (rest_init) from [<80b00d28>] (start_kernel+0x3b4/0x3c0)
[ 6.036754] ---[ end trace 677d492e50660e22 ]---
[ 6.054151] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 6.055556] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 6.055567] [drm] Driver supports precise vblank timestamp query.
[ 6.070876] Console: switching to colour frame buffer device 100x30
[ 6.080266] vc4-drm soc:gpu: fb0: frame buffer device
[ 6.920150] uart-pl011 3f201000.serial: no DMA platform data
[ 7.081933] Bluetooth: Core ver 2.22
[ 7.082013] NET: Registered protocol family 31
[ 7.082021] Bluetooth: HCI device and connection manager initialized
[ 7.082040] Bluetooth: HCI socket layer initialized
[ 7.082053] Bluetooth: L2CAP socket layer initialized
[ 7.082087] Bluetooth: SCO socket layer initialized
[ 7.169318] random: crng init done
[ 7.587763] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 7.587780] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 8.083483] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 8.793196] systemd[1]: Started ACPI event daemon.
[ 9.145328] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 9.145345] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 10.553104] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 10.636938] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 10.671765] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 11.205152] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 11.205164] brcmfmac: power management disabled
[ 12.224729] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 12.385768] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 12.385783] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 12.399687] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.824496] Bluetooth: HCI UART driver ver 2.3
[ 12.824506] Bluetooth: HCI UART protocol H4 registered
[ 12.824509] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 12.824650] Bluetooth: HCI UART protocol Broadcom registered
[ 13.267319] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.267327] Bluetooth: BNEP filters: protocol multicast
[ 13.267341] Bluetooth: BNEP socket layer initialized
[ 14.299850] Bluetooth: RFCOMM TTY layer initialized
[ 14.299880] Bluetooth: RFCOMM socket layer initialized
[ 14.299901] Bluetooth: RFCOMM ver 1.11
[ 14.804729] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 14.804745] brcmfmac: power management disabled
[ 15.255435] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 15.690610] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 16.068253] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 21.605266] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 21.605276] brcmfmac: brcmf_cfg80211_get_channel: chanspec failed (-110)
[ 22.266913] fuse init (API version 7.26)
[ 24.175295] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 24.175305] brcmfmac: brcmf_cfg80211_get_tx_power: error (-110)
[ 26.805276] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 26.805286] brcmfmac: brcmf_cfg80211_get_channel: chanspec failed (-110)
[ 29.365271] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 29.365279] brcmfmac: brcmf_cfg80211_get_tx_power: error (-110)
[ 31.925295] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 31.925304] brcmfmac: brcmf_cfg80211_get_channel: chanspec failed (-110)
[ 34.485315] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 34.485325] brcmfmac: brcmf_cfg80211_get_tx_power: error (-110)
[ 37.045347] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 37.045357] brcmfmac: brcmf_cfg80211_get_channel: chanspec failed (-110)
[ 39.605358] brcmfmac: brcmf_proto_bcdc_query_dcmd: brcmf_proto_bcdc_msg failed w/status -110
[ 39.605367] brcmfmac: brcmf_cfg80211_get_tx_power: error (-110)
[ 42.165393] brcmfmac: brcmf_cfg80211_del_station: SCB_DEAUTHENTICATE_FOR_REASON failed -110
[ 47.765489] brcmfmac: brcmf_cfg80211_stop_ap: SET SSID error (-110)
[ 50.325504] brcmfmac: brcmf_cfg80211_stop_ap: BRCMF_C_DOWN error -110
Reboot attempt 4
--------------------------------------------------------------------------------
[ 44.301821] brcmfmac: Firmware version = wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[ 44.926695] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 44.927037] cs42xx8: probe of 1-0048 failed with error -121
[ 45.626233] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 45.626253] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 45.641639] vc4-drm soc:gpu: bound 3f600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 45.646545] ------------[ cut here ]------------
[ 45.646839] WARNING: CPU: 0 PID: 441 at drivers/gpu/drm/drm_irq.c:1794 drm_handle_vblank+0x298/0x29c [drm]
[ 45.646845] Modules linked in: snd_soc_cs42xx8_i2c snd_soc_cs42xx8 binfmt_misc spidev joydev vc4(+) drm_kms_helper brcmfmac brcmutil drm cfg80211 syscopyarea sysfillrect snd_soc_bcm2835_i2s snd_soc_audioinjector_octo_soundcard sysimgblt fb_sys_fops snd_soc_core rfkill snd_compress snd_pcm_dmaengine i2c_bcm2835 snd_pcm_oss snd_mixer_oss snd_pcm snd_timer spi_bcm2835 snd bcm2835_gpiomem rpi_backlight rpi_ft5406 fixed uio_pdrv_genirq uio evdev cdc_acm i2c_dev ip_tables x_tables ipv6
[ 45.647003] CPU: 0 PID: 441 Comm: btuart Not tainted 4.9.24-v7+ #993
[ 45.647007] Hardware name: BCM2835
[ 45.647035] [<8010fb3c>] (unwind_backtrace) from [<8010c058>] (show_stack+0x20/0x24)
[ 45.647052] [<8010c058>] (show_stack) from [<80455200>] (dump_stack+0xd4/0x118)
[ 45.647068] [<80455200>] (dump_stack) from [<8011d2c4>] (__warn+0xf8/0x110)
[ 45.647081] [<8011d2c4>] (__warn) from [<8011d3ac>] (warn_slowpath_null+0x30/0x38)
[ 45.647330] [<8011d3ac>] (warn_slowpath_null) from [<7f343c70>] (drm_handle_vblank+0x298/0x29c [drm])
[ 45.647830] [<7f343c70>] (drm_handle_vblank [drm]) from [<7f343c98>] (drm_crtc_handle_vblank+0x24/0x28 [drm])
[ 45.648164] [<7f343c98>] (drm_crtc_handle_vblank [drm]) from [<7f499158>] (vc4_crtc_irq_handler+0x4c/0x94 [vc4])
[ 45.648301] [<7f499158>] (vc4_crtc_irq_handler [vc4]) from [<80173dd8>] (__handle_irq_event_percpu+0xc0/0x22c)
[ 45.648317] [<80173dd8>] (__handle_irq_event_percpu) from [<80173f70>] (handle_irq_event_percpu+0x2c/0x68)
[ 45.648330] [<80173f70>] (handle_irq_event_percpu) from [<80174000>] (handle_irq_event+0x54/0x78)
[ 45.648347] [<80174000>] (handle_irq_event) from [<80177718>] (handle_level_irq+0xb0/0x158)
[ 45.648363] [<80177718>] (handle_level_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.648387] [<80172ecc>] (generic_handle_irq) from [<8047d9e8>] (bcm2836_chained_handle_irq+0x38/0x50)
[ 45.648409] [<8047d9e8>] (bcm2836_chained_handle_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.648423] [<80172ecc>] (generic_handle_irq) from [<8017350c>] (__handle_domain_irq+0x6c/0xc4)
[ 45.648440] [<8017350c>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 45.648463] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<8071893c>] (__irq_svc+0x5c/0x7c)
[ 45.648472] Exception stack(0x881c3d68 to 0x881c3db0)
[ 45.648483] 3d60: 80c7a458 00000000 00000001 00000000 20000013 b5b91c00
[ 45.648496] 3d80: 00000339 00000000 00000300 00000000 80b79220 881c3dcc 80c040a4 881c3db8
[ 45.648504] 3da0: 80718644 80718658 60000013 ffffffff
[ 45.648522] [<8071893c>] (__irq_svc) from [<80718658>] (_raw_spin_unlock_irqrestore+0x50/0x70)
[ 45.648542] [<80718658>] (_raw_spin_unlock_irqrestore) from [<8011878c>] (check_and_switch_context+0x174/0x51c)
[ 45.648563] [<8011878c>] (check_and_switch_context) from [<80277364>] (flush_old_exec+0x330/0x720)
[ 45.648586] [<80277364>] (flush_old_exec) from [<802c9784>] (load_elf_binary+0x2c4/0x112c)
[ 45.648602] [<802c9784>] (load_elf_binary) from [<80276cf4>] (search_binary_handler+0xb0/0x24c)
[ 45.648617] [<80276cf4>] (search_binary_handler) from [<802780c4>] (do_execveat_common+0x454/0x6c0)
[ 45.648630] [<802780c4>] (do_execveat_common) from [<80278368>] (do_execve+0x38/0x40)
[ 45.648642] [<80278368>] (do_execve) from [<802785b4>] (SyS_execve+0x2c/0x30)
[ 45.648659] [<802785b4>] (SyS_execve) from [<801080c0>] (ret_fast_syscall+0x0/0x1c)
[ 45.648668] ---[ end trace b81a5114b7887e5c ]---
[ 45.668917] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 45.672616] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 45.672630] [drm] Driver supports precise vblank timestamp query.
[ 45.698253] Console: switching to colour frame buffer device 100x30
[ 45.712021] vc4-drm soc:gpu: fb0: frame buffer device
[ 45.877492] uart-pl011 3f201000.serial: no DMA platform data
[ 46.062159] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 46.062173] brcmfmac: power management disabled
[ 46.175451] Bluetooth: Core ver 2.22
[ 46.175552] NET: Registered protocol family 31
[ 46.175558] Bluetooth: HCI device and connection manager initialized
[ 46.175602] Bluetooth: HCI socket layer initialized
[ 46.175624] Bluetooth: L2CAP socket layer initialized
[ 46.175678] Bluetooth: SCO socket layer initialized
[ 47.032701] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 47.186679] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 47.186699] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 48.746222] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 48.746234] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 49.564324] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 49.657577] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 49.697914] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 50.244704] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 50.244718] brcmfmac: power management disabled
[ 50.483421] Bluetooth: HCI UART driver ver 2.3
[ 50.483430] Bluetooth: HCI UART protocol H4 registered
[ 50.483433] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 50.483556] Bluetooth: HCI UART protocol Broadcom registered
[ 50.697412] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 50.697420] Bluetooth: BNEP filters: protocol multicast
[ 50.697432] Bluetooth: BNEP socket layer initialized
[ 50.801782] Bluetooth: RFCOMM TTY layer initialized
[ 50.801807] Bluetooth: RFCOMM socket layer initialized
[ 50.801832] Bluetooth: RFCOMM ver 1.11
[ 50.945440] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 50.945457] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 50.958310] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 51.269042] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 53.935315] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 53.935346] brcmfmac: power management disabled
[ 55.205503] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 55.291304] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 55.716697] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 58.288986] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 60.541122] fuse init (API version 7.26)
Reboot attempt 5
--------------------------------------------------------------------------------
[ 43.881068] rpi-ft5406 rpi_ft5406: Probing device
[ 43.882067] input: FT5406 memory based driver as /devices/virtual/input/input3
[ 43.968611] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 44.205065] [drm] Initialized
[ 44.311611] usbcore: registered new interface driver brcmfmac
[ 44.423960] brcmfmac: Firmware version = wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[ 45.186206] cs42xx8 1-0048: found device, revision 4
[ 45.695643] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 45.695661] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 45.701549] vc4-drm soc:gpu: bound 3f600000.firmwarekms (ops vc4_fkms_ops [vc4])
[ 45.710937] ------------[ cut here ]------------
[ 45.711259] WARNING: CPU: 0 PID: 0 at drivers/gpu/drm/drm_irq.c:1794 drm_handle_vblank+0x298/0x29c [drm]
[ 45.711266] Modules linked in: snd_soc_cs42xx8_i2c snd_soc_cs42xx8 binfmt_misc joydev spidev vc4(+) brcmfmac brcmutil drm_kms_helper drm cfg80211 snd_soc_bcm2835_i2s snd_soc_audioinjector_octo_soundcard rfkill snd_soc_core syscopyarea snd_compress sysfillrect snd_pcm_dmaengine sysimgblt fb_sys_fops snd_pcm_oss snd_mixer_oss snd_pcm i2c_bcm2835 snd_timer spi_bcm2835 bcm2835_gpiomem snd rpi_backlight rpi_ft5406 fixed uio_pdrv_genirq uio evdev cdc_acm i2c_dev ip_tables x_tables ipv6
[ 45.711448] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.9.24-v7+ #993
[ 45.711453] Hardware name: BCM2835
[ 45.711490] [<8010fb3c>] (unwind_backtrace) from [<8010c058>] (show_stack+0x20/0x24)
[ 45.711513] [<8010c058>] (show_stack) from [<80455200>] (dump_stack+0xd4/0x118)
[ 45.711531] [<80455200>] (dump_stack) from [<8011d2c4>] (__warn+0xf8/0x110)
[ 45.711545] [<8011d2c4>] (__warn) from [<8011d3ac>] (warn_slowpath_null+0x30/0x38)
[ 45.711808] [<8011d3ac>] (warn_slowpath_null) from [<7f394c70>] (drm_handle_vblank+0x298/0x29c [drm])
[ 45.712314] [<7f394c70>] (drm_handle_vblank [drm]) from [<7f394c98>] (drm_crtc_handle_vblank+0x24/0x28 [drm])
[ 45.712633] [<7f394c98>] (drm_crtc_handle_vblank [drm]) from [<7f4ea158>] (vc4_crtc_irq_handler+0x4c/0x94 [vc4])
[ 45.712736] [<7f4ea158>] (vc4_crtc_irq_handler [vc4]) from [<80173dd8>] (__handle_irq_event_percpu+0xc0/0x22c)
[ 45.712752] [<80173dd8>] (__handle_irq_event_percpu) from [<80173f70>] (handle_irq_event_percpu+0x2c/0x68)
[ 45.712766] [<80173f70>] (handle_irq_event_percpu) from [<80174000>] (handle_irq_event+0x54/0x78)
[ 45.712781] [<80174000>] (handle_irq_event) from [<80177718>] (handle_level_irq+0xb0/0x158)
[ 45.712797] [<80177718>] (handle_level_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.712814] [<80172ecc>] (generic_handle_irq) from [<8047d9e8>] (bcm2836_chained_handle_irq+0x38/0x50)
[ 45.712832] [<8047d9e8>] (bcm2836_chained_handle_irq) from [<80172ecc>] (generic_handle_irq+0x34/0x44)
[ 45.712844] [<80172ecc>] (generic_handle_irq) from [<8017350c>] (__handle_domain_irq+0x6c/0xc4)
[ 45.712860] [<8017350c>] (__handle_domain_irq) from [<8010150c>] (bcm2836_arm_irqchip_handle_irq+0xa8/0xac)
[ 45.712878] [<8010150c>] (bcm2836_arm_irqchip_handle_irq) from [<8071893c>] (__irq_svc+0x5c/0x7c)
[ 45.712886] Exception stack(0x80c01f18 to 0x80c01f60)
[ 45.712895] 1f00: 00000000 b6798478
[ 45.712906] 1f20: 00000000 00000000 80c00000 80c0312c 00000001 80c03198 80c15e86 80c15e86
[ 45.712918] 1f40: b6fff9c0 80c01f74 80c040a4 80c01f68 80108a54 80108a58 60000013 ffffffff
[ 45.712937] [<8071893c>] (__irq_svc) from [<80108a58>] (arch_cpu_idle+0x34/0x4c)
[ 45.712953] [<80108a58>] (arch_cpu_idle) from [<80718094>] (default_idle_call+0x34/0x48)
[ 45.712968] [<80718094>] (default_idle_call) from [<80161c3c>] (cpu_startup_entry+0xe4/0x160)
[ 45.712987] [<80161c3c>] (cpu_startup_entry) from [<80712920>] (rest_init+0x84/0x88)
[ 45.713007] [<80712920>] (rest_init) from [<80b00d28>] (start_kernel+0x3b4/0x3c0)
[ 45.713016] ---[ end trace 2261afb846f17d82 ]---
[ 45.722475] vc4-drm soc:gpu: bound 3fc00000.v3d (ops vc4_v3d_ops [vc4])
[ 45.723734] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 45.723744] [drm] Driver supports precise vblank timestamp query.
[ 45.745012] Console: switching to colour frame buffer device 100x30
[ 45.753683] vc4-drm soc:gpu: fb0: frame buffer device
[ 46.462886] uart-pl011 3f201000.serial: no DMA platform data
[ 46.636149] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 46.636166] brcmfmac: power management disabled
[ 46.693124] Bluetooth: Core ver 2.22
[ 46.693259] NET: Registered protocol family 31
[ 46.693265] Bluetooth: HCI device and connection manager initialized
[ 46.693289] Bluetooth: HCI socket layer initialized
[ 46.693304] Bluetooth: L2CAP socket layer initialized
[ 46.693340] Bluetooth: SCO socket layer initialized
[ 47.259019] audioinjector-octo soc:sound: cs42448 <-> 3f203000.i2s mapping ok
[ 47.651472] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 49.090001] systemd[1]: Started CUPS Scheduler.
[ 49.091506] systemd[1]: Started ACPI event daemon.
[ 49.890119] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 49.976915] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 50.006959] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 50.357164] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 50.386470] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 50.390353] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 50.409746] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 50.535013] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 50.535028] brcmfmac: power management disabled
[ 51.564030] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 51.916783] Bluetooth: HCI UART driver ver 2.3
[ 51.916793] Bluetooth: HCI UART protocol H4 registered
[ 51.916796] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 51.916935] Bluetooth: HCI UART protocol Broadcom registered
[ 52.288083] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 52.288100] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 52.312462] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 52.331060] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 52.331069] Bluetooth: BNEP filters: protocol multicast
[ 52.331082] Bluetooth: BNEP socket layer initialized
[ 52.560797] Bluetooth: RFCOMM TTY layer initialized
[ 52.560828] Bluetooth: RFCOMM socket layer initialized
[ 52.560850] Bluetooth: RFCOMM ver 1.11
[ 53.410336] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 53.410358] brcmfmac: power management disabled
[ 55.365993] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 55.798513] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 56.010241] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 57.383045] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
[ 59.016027] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 59.016820] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 59.060701] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 61.839143] fuse init (API version 7.26)
[ 75.616623] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 75.646718] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 75.650311] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 75.656626] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 80.798212] bcm2835-dma 3f007000.dma: DMA transfer could not be terminatedUPDATE: Not using the vc4-fkms-v3d overlay doesn't appear to really solve anything. The Octo still failed to load intermittently on 3 out of 5 reboot attempts.
UPDATE 2: Going further, I commented out the rpi-ft5406 (touchscreen) overlay and set ignore_lcd=1 in config.txt and booted up with an HDMI screen connected instead. The first reboot worked (I had sound), but I could see that the first load attempt of the Octo still failed, while the second attempt apparently worked.
Code: Select all
[ 6.056162] cs42xx8 1-0048: found device, revision 4
[ 6.076448] usbcore: registered new interface driver brcmfmac
[ 6.270184] brcmfmac: Firmware version = wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[ 7.156896] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 7.156906] brcmfmac: power management disabled
[ 7.439754] uart-pl011 3f201000.serial: no DMA platform data
[ 7.515750] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 7.515770] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 8.937639] random: crng init done
[ 8.976937] Bluetooth: Core ver 2.22
[ 8.977090] NET: Registered protocol family 31
[ 8.977102] Bluetooth: HCI device and connection manager initialized
[ 8.977142] Bluetooth: HCI socket layer initialized
[ 8.977169] Bluetooth: L2CAP socket layer initialized
[ 8.977254] Bluetooth: SCO socket layer initialized
[ 9.079533] audioinjector-octo soc:sound: cs42448 <-> 3f203000.i2s mapping ok
Code: Select all
[ 45.359930] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 45.360304] cs42xx8: probe of 1-0048 failed with error -121
[ 45.726828] uart-pl011 3f201000.serial: no DMA platform data
[ 46.205256] audioinjector-octo soc:sound: ASoC: CPU DAI (null) not registered - will retry
[ 46.205277] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 46.240976] Bluetooth: Core ver 2.22
[ 46.241066] NET: Registered protocol family 31
[ 46.241071] Bluetooth: HCI device and connection manager initialized
[ 46.241092] Bluetooth: HCI socket layer initialized
[ 46.241106] Bluetooth: L2CAP socket layer initialized
[ 46.241144] Bluetooth: SCO socket layer initialized
[ 46.735274] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 46.735291] brcmfmac: power management disabled
[ 47.766289] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 47.766308] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
Code: Select all
[ 5.696564] cs42xx8 1-0048: found device, revision 4
[ 5.701914] brcmfmac: Firmware version = wl0: Aug 29 2016 20:48:16 version 7.45.41.26 (r640327) FWID 01-4527cfab
[ 6.771398] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6.771407] brcmfmac: power management disabled
[ 6.908649] audioinjector-octo soc:sound: cs42448 <-> 3f203000.i2s mapping ok
[ 7.842154] uart-pl011 3f201000.serial: no DMA platform data
[ 7.869740] Bluetooth: Core ver 2.22
[ 7.869849] NET: Registered protocol family 31
[ 7.869855] Bluetooth: HCI device and connection manager initialized
[ 7.873530] Bluetooth: HCI socket layer initialized
[ 7.873554] Bluetooth: L2CAP socket layer initialized
[ 7.873595] Bluetooth: SCO socket layer initialized
[ 8.079325] random: crng init done
[ 9.497936] Adding 102396k swap on /var/swap. Priority:-1 extents:3 across:208896k SSFS
[ 9.885162] systemd[1]: Started ACPI event daemon.
[ 13.237987] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.327239] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[ 13.353655] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 13.396891] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 13.426467] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 13.430123] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 13.450921] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 13.884102] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 13.884113] brcmfmac: power management disabled
[ 14.005070] Bluetooth: HCI UART driver ver 2.3
[ 14.005081] Bluetooth: HCI UART protocol H4 registered
[ 14.005084] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 14.005225] Bluetooth: HCI UART protocol Broadcom registered
[ 14.938446] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 15.750515] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.750524] Bluetooth: BNEP filters: protocol multicast
[ 15.750537] Bluetooth: BNEP socket layer initialized
[ 16.094530] brcmfmac: brcmf_p2p_create_p2pdev: set p2p_disc error
[ 16.094545] brcmfmac: brcmf_cfg80211_add_iface: add iface p2p-dev-wlan0 type 10 failed: err=-16
[ 16.154804] Bluetooth: RFCOMM TTY layer initialized
[ 16.154821] Bluetooth: RFCOMM socket layer initialized
[ 16.154842] Bluetooth: RFCOMM ver 1.11
[ 17.231420] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.380315] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 18.380326] brcmfmac: power management disabled
[ 18.669465] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 18.835052] nf_conntrack version 0.5.0 (14336 buckets, 57344 max)
[ 19.071949] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
[ 19.150320] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 21.694235] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 21.695036] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 22.300522] brcmfmac: brcmf_cfg80211_stop_ap: setting INFRA mode failed -7
[ 24.521549] fuse init (API version 7.26)
[ 40.635347] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 40.665468] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 40.669133] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 40.675693] bcm2835-i2s 3f203000.i2s: I2S SYNC error!
[ 45.835266] bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
Code: Select all
[ 5.755720] cs42xx8 1-0048: failed to get device ID, ret = -121
[ 5.756072] cs42xx8: probe of 1-0048 failed with error -121
[ 6.455743] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6.455751] brcmfmac: power management disabled
[ 6.695278] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 6.695298] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
[ 6.779876] uart-pl011 3f201000.serial: no DMA platform data
[ 8.255227] audioinjector-octo soc:sound: ASoC: CODEC DAI cs42448 not registered - will retry
[ 8.255247] audioinjector-octo soc:sound: snd_soc_register_card failed (-517)
Re: Octo arrived and working, potentiometer knobs?
I've removed the MoPower UPS from my setup for now. I got my access point working again using NetworkManager and dnsmasq. I've found that shairport-sync doesn't support cards with more than 2 channels, so I suppose that explains why it isn't working.
Code: Select all
shairport-sync[22297]: audio_alsa: Channels count (2) not available for device "hw:0": Invalid argumentWho is online
Users browsing this forum: No registered users and 3 guests